201000 Self-Tapping - Countersunk Head, Zinc Plated Steel
Self Tapping screws are an excellent, economical general purpose fastener. Capable of self drilling into medium density timbers but with the strength to provide a strong hold when used in pre drilled holes in sheet. Can by power or hand driven. Coated Zinc Clear (ZC) which provides a bright silver finish and is suitable for internal use but can be used externally if painted or otherwise protected.
• An economical general purpose fastener which can perform as a self-drilling screw in medium density timbers and very popular when used as a self tapping screw for Sheetmetal applications
• Available in a wide range of sizes and lengths
• The Zinc Plated finish is recommended for internal use only but can be used externally if adequately painted or protected
• Available in a wide range of sizes and lengths
• The Zinc Plated finish is recommended for internal use only but can be used externally if adequately painted or protected
1/ Ensure the correct driver tool is fitted to your power drill or screw driver. Can also be driven by hand screw driver.
2/ Place the screw on the driver tool and position it onto the materials being fastened.
3/ If necessary push sharply to create a centre mark and to prevent screw wander.
4/ Squeeze trigger and maintain steady, constant pressure until the screw has drilled and fastened.
Recommended Driving speed is approximately 800~1,000 r.p.m.
Note:-
Hardwoods may require a pilot hole to be pre-drilled as this will assist the screw in tapping a thread whilst reducing timber splitting and driving torque.
Sheet metal must be pre-drilled with a pilot hole.
For information on the correct size pilot hole to drill refer to our Technical data section for Self Tapping Screws.
2/ Place the screw on the driver tool and position it onto the materials being fastened.
3/ If necessary push sharply to create a centre mark and to prevent screw wander.
4/ Squeeze trigger and maintain steady, constant pressure until the screw has drilled and fastened.
Recommended Driving speed is approximately 800~1,000 r.p.m.
Note:-
Hardwoods may require a pilot hole to be pre-drilled as this will assist the screw in tapping a thread whilst reducing timber splitting and driving torque.
Sheet metal must be pre-drilled with a pilot hole.
For information on the correct size pilot hole to drill refer to our Technical data section for Self Tapping Screws.
• Ideal for hinges, brackets, joinery, cabinetmaking, etc., and general fastening to timber and thin metal.
• Commonly used in plastic plugs and spaghetti when fixing into masonry.
• Commonly used in plastic plugs and spaghetti when fixing into masonry.
| Size | Coating | Pack Type | 520 Y Thread Length (TL) | 530 Y Driver Tool | Code |
|---|---|---|---|---|---|
| 4g x 3/8" (10mm) |
|
||||
| 4g x 1/2" (12mm) |
|
||||
| 4g x 5/8" (16mm) |
|
||||
| 4g x 3/4" (20mm) |
|
||||
| 4g x 1" (25mm) |
|
||||
| 5g x 5/8" (16mm) |
|
||||
| 5g x 3/4" (20mm) |
|
||||
| 6g x 1/2" (12mm) |
|
||||
| 6g x 5/8" (16mm) |
|
||||
| 6g x 3/4" (20mm) |
|
||||
| 6g x 1" (25mm) |
|
||||
| 6g x 1 1/4" (32mm) |
|
||||
| 6g x 1 1/2" (38mm) |
|
||||
| 8g x 1/2" (12mm) |
|
||||
| 8g x 5/8" (16mm) |
|
||||
| 8g x 3/4" (20mm) |
|
||||
| 8g x 1" (25mm) |
|
||||
| 8g x 1 1/4" (32mm) |
|
||||
| 8g x 1 1/2" (38mm) |
|
||||
| 8g x 1 3/4" (45mm) |
|
||||
| 8g x 2" (50mm) |
|
||||
| 10g x 3/4" (20mm) |
|
||||
| 10g x 1" (25mm) |
|
||||
| 10g x 1 1/4" (32mm) |
|
||||
| 10g x 1 1/2" (38mm) |
|
||||
| 10g x 1 3/4" (45mm) |
|
||||
| 10g x 2" (50mm) |
|